stegosaurus

Making Large Paper Mache Dinosaurs – pt 3

/ Marjorie Sanpietro / Leave a comment

Progress goes slowly on the dinosaur. I’ve lost my helpers to Minecraft Dungeons…and the mastermind is not in love with the craft of paper mache. He does not love the glue on his hands.

Mr. Stegosaurus now has firmly attached feet. I ran strips lengthwise from the bottom of the feet up both sides of the leg and then wrapped additional strips around the leg.

I’m working on attaching the spines. I used what the boys drew and made more. I think I’ll need about 10 pairs of spines in varying sizes to finish. I used the handy-dandy masking tape from Scotch that doesn’t suck and went to town. One tip I can share – I attached the spines together where they met and hopefully gave them more stability.

I’ll reinforce them with more strips and glue and then add paper mache clay to give them detail. The next big task is making the paper mache clay. I’ll use the clay to smooth out my sculpture and add finer details – besides accenting the spines. I’m thinking toes, facial features, and bumps for knees are possibilities.

Three ingredients that I remember off the top of my head are joint compound, toilet paper and PVA glue (like white Elmer’s). I’m interested in how far the recipe from Ultimate Paper Mache that I plan on following will go in covering Mr. Stegosaurus. I think I’ll probably need multiple batches.

If I continue the dino paper mache saga – I’ll start cutting out the T-Rex. I feel like he is going to be more difficult – because he’ll be standing up on two back legs. Luckily, I found these cardboard boot inserts that I might use for his feet. They seem heavier and like they would give him more stability.

Stay tuned and comment below! What’s the craziest thing you have made for your kids?

Making Large Paper Mache Dinosaurs – pt.1

/ Marjorie Sanpietro / Leave a comment

My 6 year old is a very creative kid and when he decided that we needed to make were some BIG dinosaurs – my brain went right to paper mache for this project because it’s inexpensive and these dinosaurs don’t need to weigh 100lbs each.

I was really impressed when I suggested it to him, because he knew exactly what I was talking about and related it to a display he had seen at school. He decided that he’d like us to make a stegosaurus first AND THEN if that worked out, we could try a T-rex. 

To begin with, I needed some reference material. We looked at a couple of his dinosaur books so I could get a general shape for this stegosaurus. I drew and cut the torso pieces out. I created the head and tail pieces separately so that I could try to position them a little different from the rest of the body – realism counts when you’re making dinosaurs, y’all.

The boys helped me out by tracing my first pieces onto other cardboard – you need at least two of everything to give it some volume because we’re going for 3D! They also helped by making some plates, spikes, and feet for the stegosaurus to be used later. 

To continue building the shape, I connected the top of the stegosaurus more narrowly than at the bottom. I attached the main pieces by adding strips of cardboard of the correct width along the sides and held the whole thing together with masking tape, slightly angling the head and tail. Before I closed Mr. Stegosaurus completely up, I stuffed him with recycled newspaper to give him some mass for better stability.

Here’s Mr. Dinosaur in our living room – hanging out waiting to be permanently sealed up – you can see the tape starting to have some problems.

I’m not sure what was going on with the masking tape – maybe it was too cheap for the job? We put the stegosaurus aside for a few days but the situation became critical when it didn’t seem to be staying together anymore. 

It was definitely time for some good old fashioned glue and paper. I typically use an approximate 50/50 mixture of water and PVA glue. We tore up scrap paper and pasted it on the frame of Mr. Stegosaurus – sealing up all the seams and making any last minute adjustments.

Next we started bulking up the body. I used paper towel rolls to begin forming the legs and then larger pieces of paper scrunched and otherwise manipulated to add more body.

At this point – we were using the same crappy masking tape and I got frustrated – so it’s been sitting for about a week now. I did go buy some better masking tape. We’ll see how it goes…to be continued.

Comment below if you’re excited to know how this project turns out!